Skip to main content

Managing Route Sequence

Published: 2025-11-17      Revised: 2026-11-13

Route Sequence is a number on each component that sets the physical order the technician should monitor in. In a tour in Chateau Mobile, components are listed by LUnit, then Route Sequence, then Tag.

This article covers:

Tools for reviewing your route sequence​

  • Components and Inspections grids: sort and filter by inspection times and other properties to see the order components were actually inspected in.
  • Scout Map: shows the paths technicians followed during their tours.
  • Bad Routes audit: lets technicians flag possible route sequence problems for you to review. We recommend turning it on in Porches > Audit Settings while your route sequences are being built or reviewed.

Fixing a few components​

To fix a few components that are out of order, edit each component and change its Route Sequence field. This goes through the normal MOC process.

Tip: Route Sequence accepts decimals. To place a component between 10 and 11 without renumbering the others, give it 10.5.

Resequencing many components with Modify Route Sequence​

Modify Route Sequence on the Components grid renumbers a group of components in one step, in the order they are sorted in the grid.

  • Who can use it: only users with the Approver role. For everyone else the button is greyed out.
  • When it takes effect: immediately. It skips the MOC Porch, and each change is recorded in the component's history.

Step 1: Load and sort the components​

  1. Go to Components and run a query that returns the components you want to resequence (for example, one LUnit).
  2. Sort the grid into the order you want them monitored. To sort by more than one column, hold Shift and click each column header in order. A small number in each header shows its place in the sort order. Make sure each column is sorted the right way (ascending or descending) before you shift-click the next one.
  3. Select all the components you want to resequence.

Important: Chateau numbers the selected components in the order they appear in the grid. Check the sort before you continue.

Step 2: Open the dialog and set the numbers​

  1. Click Modify Route Sequence. The dialog repeats the sorting instructions from Step 1. If your grid is already sorted and selected, skip them.
  2. Starting route sequence number: enter the number for the first component in the grid. This field is required.
  3. Increment the route sequence number by: enter how much to add for each component after the first. The default is 1.
  4. Click Set Route Sequence.

Example: with a starting number of 100 and an increment of 10, the first five components get 100, 110, 120, 130 and 140. Using an increment larger than 1 leaves gaps, so you can add new components later without renumbering everything.

Both fields accept up to three decimal places.

Step 3: Check the result​

Re-run your query and sort by Route Sequence to confirm the new order. Tours built after the change use the new sequence. If a tour is already checked out to a handheld, check it in and check it out again to get the new order.

If you see Problem Setting Route Sequence, try again. If it fails a second time, contact LDARtools Support.

Using the order a tour was monitored as the route sequence​

If a technician walked a tour in a good order, you can save that order as the route sequence.

  1. Go to Components and query for the components that were inspected. For example, use the LUnit and Last M21 Performed (or Last AVO Performed / Last OGI Performed) on or after the date of the tour.
  2. Sort the Last M21 Performed column ascending, so the first component inspected is at the top.
  3. Select all the components.
  4. Click Modify Route Sequence and follow Step 2 above.

Warning: If more than one technician monitored the same LUnit that day, their inspection times will be mixed together. Query for one technician's components at a time so the order isn't scrambled.

Changing route sequence in Chateau Mobile​

You can change the route sequence of one component at a time in Chateau Mobile. Modify Route Sequence is only available in Chateau on a computer.

  1. Open the component's Component Details.
  2. Tap Route Sequence, enter the new number and tap the blue tick.
  3. Tap Save and choose a Change Why.

If you have the Approver role, the change takes effect when you check in. Otherwise it is sent to the MOC Porch for approval. See Component Management.

Note: The sort dropdown on a tour's component list in Chateau Mobile can show components by Route Sequence or by Tag Number. Changing it changes only the order you see on the handheld, not the component's Route Sequence.

Other options for building route sequences​

  • Contact LDARtools Support to set up route sequences from your past inspection records, or from another order you prefer.
  • Sort tours by tag instead: if your tag numbers already follow the order you want them inspected in, go to Settings > Miscellaneous and turn on Sort Tours by LUnit then Tag (not Route Sequence).
  • Add Via Photo: if you have a component mapping or retagging project coming up, you can use Add Via Photo to enter new route sequences as you tag.